Europa-List Digest Server wrote:
>
> *
>
> ==================================================
> Online Versions of Today's List Digest Archive
> ==================================================
>
> Today's complete Europa-List Digest can be also be found in either
> of the two Web Links listed below. The .html file includes the Digest
> formatted in HTML for viewing with a web browser and features Hyperlinked
> Indexes and Message Navigation. The .txt file includes the plain ASCII
> version of the Europa-List Digest and can be viewed with a generic
> text editor such as Notepad or with a web browser.
>
> HTML Version:
>
>
> http://www.matronics.com/digest/europa-list/Digest.Europa-List.2003-12-27.html
>
> Text Version:
>
>
> http://www.matronics.com/digest/europa-list/Digest.Europa-List.2003-12-27.txt
>
> ================================================
> EMail Version of Today's List Digest Archive
> ================================================
>
>
> Europa-List Digest Archive
> ---
> Total Messages Posted Sat 12/27/03: 2
>
>
> Today's Message Index:
> ----------------------
>
> 1. 03:52 AM - Re: Tachometer connection for 914 to EIS (G-IANI)
> 2. 05:07 PM - Re: 'bid, anybody know offhand what..... (Troy Maynor)
>
>
>
> ________________________________ Message 1
> _____________________________________
>
> From: "G-IANI" <g-iani@ntlworld.com>
> Subject: RE: Europa-List: Tachometer connection for 914 to EIS
>
>
> I had trouble with this. Pins 13 and 26 on the TCU are the Tacho output. I
> have feed TCU pin 26 to pin 2 on the Rotax Tacho and TCU pin 13 to Rotax
> Tacho Pin 3 (Rotax Tacho Pin 1 is +12V). TCU Pin 26 is also connected (in
> parallel) to pin 5 on the EIS . Both the Rotax tacho and the EIS appear to
> display RPM OK.
>
> Your note had me scanning the circuit diagrams I had produced to find that
> they were not a perfect record of what I had done. So I had to spend a few
> minutes to pull the panel off (again).
>
> Ian Rickard #505 G-IANI (Very nearly ready o fly)
> Europa Club Assistant Mods Rep
> e-mail mods@europaclub.org.uk
>
> -----Original Message-----
> From: owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com]On Behalf Of Paul
> McAllister
> Subject: Europa-List: Tachometer connection for 914 to EIS
>
> <paul.mcallister@qia.net>
>
> Hi all,
>
> I was wondering if someone out there who has connected an EIS to a 914 can
> help with the tachometer connection. The Grand Rapids manual show a generic
> 912/914 connection, however when looking in the 914 installation manual it
> shows two wires from the TCU for the tachometer. Is this what is used for
> the EIS or is it done differently. ?
>
> Thanks, Paul
>
> ________________________________ Message 2
> _____________________________________
>
> From: "Troy Maynor" <wingnut54@charter.net>
> Subject: RE: Europa-List: 'bid, anybody know offhand what.....
>
>
> I think it was someone at the factory that told me. Look at Rutan Fiberglass
> Cloths on page 30 in the '03-'04 ACS catalog. Part number RA7725. It is the
> same as factory I was told and I can't see any difference.
> Troy Maynor
> N120EU Monowheel Classic
> Left to finish:
> Paint,interior,engine install, wiring.
>
> > -----Original Message-----
> > From: owner-europa-list-server@matronics.com
> > [mailto:owner-europa-list-server@matronics.com]On Behalf Of
> > TELEDYNMCS@aol.com
> > Sent: Friday, December 26, 2003 12:12 PM
> > To: europa-list@matronics.com
> > Subject: Europa-List: 'bid, anybody know offhand what.....
> >
> >
> >
> > Greetings,
> >
> > Does anybody know the weight of the 'bid supplied with the kit?
> > I've looked
> > all over the manual and it doesn't specify. I'm almost out and I
> > need to order
> > some more, along with a few other things from ACS.
> >
> > Thanks!
> >
> > Regards,
> >
> > John Lawton
> > Dunlap, TN
> > A-245 (Today: Vacuum bagging baggage bay supports and final
> > installation and
> > glassing of the tie bar)
> >
> > Completed so far:
> >
> > Wings - closed, incidence set, ailerons, flaps and wings ready to start
> > finish process.
> > Fuselage - CM installed, TP torque tube, mass balance and trim installed.
> > Flap actuator installed. Landing gear installed. Overhead console
> > and conduit
> > finished. Center console cut-a-way complete.
> > Panel - Flight instruments mounted, then removed and ready for paint
> >
> >
>
>
>
>
>
>
>
>
>
>
>
|